收藏本站
A Product Line of
Diodes Incorporated
ZXLD1362
Application Information
Setting Nominal Average Output Current with External
Resistor R S
The nominal average output current in the LED(s) is determined by
the value of the external current sense resistor (R S ) connected
between V IN and I SENSE and is given by:
I OUTnom = 0.1/R S [for R S > 0.1 ? ]
The table below gives values of nominal average output current for
several preferred values of current setting resistor (R S ) in the typical
Output Current Adjustment by PWM Control
Directly driving ADJ input
A Pulse Width Modulated (PWM) signal with duty cycle D PWM can
be applied to the ADJ pin, as shown below, to adjust the output
current to a value above or below the nominal average value set
by resistor R S :
PWM
V ADJ
application circuit shown on page 1:
ADJ
ZXLD1362
R S ( Ω )
0.1
0.13
Nominal average output
current (mA)
1000
760
0V
GND
GND
0.15
667
Driving the ADJ Input via Open Collector Transistor
The above values assume that the ADJ pin is floating and at a
nominal voltage of V REF (= 1.25V). Note that R S = 0.1 ? is the
minimum allowed value of sense resistor under these conditions to
maintain switch current below the specified maximum value.
The recommended method of driving the ADJ pin and controlling
the amplitude of the PWM waveform is to use a small NPN
switching transistor as shown below:
It is possible to use different values of R S if the ADJ pin is driven
from an external voltage. (See next section).
Output Current Adjustment by External DC Control
PWM
ADJ
ZXLD1362
GND
Voltage
The ADJ pin can be driven by an external dc voltage (V ADJ ), as
shown, to adjust the output current to a value above or below the
nominal average value defined by R S .
?
GND
This scheme uses the 50k resistor between the ADJ pin and the
internal voltage reference as a pull-up resistor for the external
transistor.
+
ADJ
ZXLD1362
Driving the ADJ Input from a Microcontroller
DC
GND
Another possibility is to drive the device from the open drain output
of a microcontroller. The diagram below shows one method of
doing this:
GND
MCU
3.3k
The nominal average output current in this case is given by:
I OUTdc = (V ADJ /1.25) x (100mV/R S ) [for 0.3< V ADJ <2.5V]
Note that 100% brightness setting corresponds to V ADJ = V REF .
When driving the ADJ pin above 1.25V, R S must be increased in
proportion to prevent I OUTdc exceeding 1A maximum.
ADJ
ZXLD1362
GND
The input impedance of the ADJ pin is 50k ? ±25% for voltages
below V REF and 14.2k ? ±25% for voltages above V REF +100mV.
If the NMOS transistor within the microcontroller has high Gate /
Drain capacitance, this arrangement can inject a negative spike
into ADJ input of the 1362 and cause erratic operation but the
addition of a Schottky clamp diode (cathode to ADJ) to ground and
inclusion of a series resistor (3.3k) will prevent this. See the
section on PWM dimming for more details of the various modes of
control using high frequency and low frequency PWM signals.
ZXLD1362
Document number: DS33472 Rev. 5 - 2
17 of 24
www.diodes.com
May 2012
? Diodes Incorporated
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
ZXLD1366DACTC IC LED DRIVER WHITE BCKLGT 6-DFN
ZXLD1370EST16TC IC LED DRVR HIGH BRIGHT TSSOP-16
ZXLD1371QESTTC IC LED DRIVER
ZXLD1374EST20TC IC LED DVR BUCK BOOST 20TSSOP
ZXLD1937ET5TA IC LED DRIVR WHITE BCKLGT TSOT-5
ZXLD381FHTA IC LED DRIVR WHITE BCKLT SOT23-3
ZXLD383ET5TA IC LED DRIVR WHITE BCKLGT TSOT-5
ZXSC300E5TA IC LED DRVR WHITE BCKLGT SOT23-5
相关代理商/技术参数
ZXLD1362ET5TA-CUT TAPE 制造商:DIODES 功能描述:ZXLD1362 Series 1 A 1 MHz SMT LED Driver with Internal Switch - TSOT-23-5
ZXLD1366 制造商:DIODES 制造商全称:Diodes Incorporated 功能描述:High accuracy 1A, 60V LED driver with internal switch
ZXLD1366_10 制造商:DIODES 制造商全称:Diodes Incorporated 功能描述:HIGH ACCURACY 1A, 60V LED DRIVER WITH INTERNAL SWITCH
ZXLD1366DACTC 功能描述:LED照明驱动器 1A, 60V LED Drver, Int Swtch RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
ZXLD1366DACTC-CUT TAPE 制造商:DIODES 功能描述:ZXLD1366 Series 1A 500 kHz High Accuracy LED Driver with Internal Switch - DFN-6
ZXLD1366EN8TC 功能描述:电流和电力监控器、调节器 LED DRVR W/ INT SW 1A 60V RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel
ZXLD1366ET5TA 功能描述:LED照明驱动器 1A, 60V LED Drver, Int Swtch RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
ZXLD1370 制造商:DIODES 制造商全称:Diodes Incorporated 功能描述:60V HIGH ACCURACY BUCK/BOOST/BUCK-BOOST LED DRIVER CONTROLLER